• Features:
  Zoeller′s time tested design experience gives you the needed back up performance and reliability.
• Pumps :
  12 volt highly efficient with noncorrosive pump construction.
• PRIMARY SUMP PUMP NOT INCLUDED. MUST BE ORDERED SEPARATELY.
• Control boxes :
  All models have battery burn out and overcharge protection. Models 507 and 510 have a self contained 10 amp battery recharger. All systems are fully solid state automatic controllers with alarms, light indicators, and have warning systems.
• Light indicators :
  (Long Lasting Led)
  • Power supply ′′on′′
  • Run light Battery partially charged
  • Battery fully charged Pump alarm ′′off′′
• Alarms :
  • Continuous steady beep - ′′low battery′′
  • Slow interrupted beep - ′′partially discharged battery′′ (Model 510 only)
• Control device :
  Reliable low voltage float switch.

  For Additional Information including Performance Curve

For Additional Information including Performance Curve

• FM listed motor for Class 1, Division 1, Group C & D environments.
• Warning : Not for use in acidic, methanol, or ethyl acetate atmospheres.
• Non-clogging vortex impeller design bronze class 88-8-0-4.
• Stainless steel rotor shaft.
• Durable cast construction. Cast iron cover, motor adapter and pump housing. No sheet metal parts to rust or corrode. All cast iron class 30,30000# tensile strength.
• Stainless steel screws and handle.
• 20 ft. UL Listed 5-wire (1PH) or 8-wire (3PH) neoprene cord. Extra cords lengths available in 25′-35′-50′ length only. Sensor leads & power leads in one cord for easy installation.
• 1 1/4′′ NPT threaded conduit connection for protecting cords in those extra heavy duty applications
• Moisture sensors prewired in motor housing (requires indicator in panel).
• Zoeller custom designed panels with intrinsically safe relays and moisture indicator are required.
• 3 phase models available.
• Motor - 60 Hz, 3450 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protected (3 phase requires circuit in control panel).
• Maximum temperature for sewage or dewatering 104°F (40°C).
• Shaft Seal - Stainless steel wetted parts, carbon & ceramic rotary face seal.
• Upper ball bearing and lower ball bearing running in bath of oil.
• Buna-n square ring seals.
• All models pass 2′′ spherical solids.
• Major width 13 5/16′′. Height 22′′.
• Available in nonautomatic units only.
• When ordering specify 2′′ or 3′′ NPT female flanged vertical discharge.
• 100% computerized testing and 100% tested submerged in water.
• Corrosion resistant powder coated epoxy finish.

For Additional Information including Performance Curve

• FM listed motor for Class 1, Division 1, Group C & D environments.
• Not for use in acidic, methanol, or ethyl acetate atmospheres.
• Non-clogging cast iron vortex impeller design.
• Stainless steel rotor shaft.
• Durable cast construction. Cast iron cover, motor adapter and pump housing. No sheet metal parts to rust or corrode. All cast iron class 30, 30000# tensile strength.
• Stainless steel screws and handle.
• 20 ft. UL listed 5-wire (1 PH) or 8-wire (3 PH) neoprene cord. Extra cords lengths available in 25′-35′- 50′ length only. Sensor leads & power leads in one cord for easy installation.
• 1 1/4′′ Threaded conduit connection for protecting cords in those extra heavy duty applications.
• Moisture sensors prewired in motor housing (requires indicator in panel).
• Zoeller custom designed mechanical switch or panel with intrinsically safe relays and moisture indicator is required.
• 3 phase models available.
• Motor - 60 Hz, 1750 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protected (3 Phase requires circuit in control panel).
• Maximum temperature for sewage or dewatering 104°F (40°C).
• Shaft Seal - Stainless steel wetted parts, carbon & ceramic rotary face seal.
• Upper ball bearing and lower ball bearing running in bath of oil.
• Buna-n square ring seals used throughout
• All models pass 2′′ spherical solids.
• Major width 13 9/16′′, Height 23 1/4′′.
• Available in nonautomatic units only.
• When ordering specify 2′′ or 3′′ NPT female flanged vertical discharge.
• 100% computerized testing and 100% tested sub merged in water.
• Corrosion resistant powder coated epoxy finish.

For Additional Information including Performance Curve

• FM listed motor for Class 1, Division 1, Group C & D environments.
• Warning : Not for use in acidic, methanol, or ethyl acetate atmospheres.
• Non-clogging vortex impeller design bronze class 88-8-0-4.
• Stainless steel rotor shaft.
• Durable cast construction. Cast iron cover, motor adapter and pump housing. All cast iron class 30, 30000# tensile strength.
• 20 ft. UL Listed 5-wire (1 PH) or 8-wire (3 PH) neoprene cord. Extra cords lengths available in 25′-35′-50′ length only. Sensor leads & power leads in one cord for easy installation.
• Threaded conduit connection for protecting cords in those extra heavy duty applications.
• Moisture sensors prewired in motor housing (requires indicator in panel).
• Zoeller custom designed mechanical switch or panel with intrinsically safe relays and moisture indicator is required.
• 3 phase models available.
• Motor- 60 Hz, 3450 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protected (3 phase requires circuit in control panel).
• Maximum temperature for effluent or dewatering 104° F (40°C).
• Shaft Seal - Stainless steel wetted parts, carbon & ceramic rotary face seal.
• Upper ball bearing and lower ball bearing running in bath of oil.
• Buna-n square ring seals.
• All models pass 3/4′′ spherical solids.
• Major width 13 5/16′′. Height 23′′.
• Available in nonautomatic units only.
• 1 1/2 NPT discharge standard, 2′′ & 3′′ NPT Flange available.
• 100% computerized testing and 100% tested submerged in water.
• Corrosion resistant powder coated epoxy finish, with stainless steel screws and handle.

For Additional Information including Performance Curve

• FM listed motor for Class 1, Division 1, Group C & D environments.
• Not for use in acidic, methanol, or ethyl acetate atmospheres.
• Non-clogging vortex impeller design bronze class 88-8-0-4.
• Stainless steel rotor shaft.
• Durable cast construction. Cast iron cover, motor adapter and pump housing. No sheet metal parts to rust or corrode. All cast iron class 30, 30000# tensile strength.
• Stainless steel screws and handle.
• 20 foot UL Listed 5-wire (1 Ph) or 8-wire (3 Ph) neoprene cord. Extra cords lengths available in 25′-35′-50′ length only. Sensor leads & power leads in one cord for easy installation.
• 1 1/4′′NPT threaded conduit connection for protecting cords in those extra heavy duty applications.
• Moisture sensors prewired in motor housing (requires indicator in panel).
• Zoeller custom designed panels with intrinsically safe relays and moisture indicator are required.
• 3 phase models available.
• Motor - 60 Hz, 3450 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protected (3 phase requires circuit in control panel).
• Maximum temperature for effluent or dewatering 104°F (40°C).
• Shaft Seal - Stainless steel wetted parts, carbon & ceramic rotary face seal.
• Upper ball bearing and lower ball bearing running in bath of oil.
• Buna-n square ring seals.
• All X 180 series pass 3/4′′ spherical solids.
  Model X 191 pump passes 5/8′′ spherical solids.
• Major width 13 5/16. Height 23′′.
• Available in nonautomatic units only.
• 1 1/2′′ NPT discharge standard, 2′′ & 3′′ NPT Flange available.
• 100% computerized testing and 100% tested sub merged in water.
• Corrosion resistant powder coated epoxy finish.
  Note: The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles

  For Additional Information including Performance Curve

• FM listed motor for Class 1, Division 1, Group C & D environments.
• Not for use in acidic, methanol, or ethyl acetate atmospheres.
• Non-clogging vortex impeller design bronze class 88-8-0-4.
• Stainless steel rotor shaft.
• Durable cast construction. Cast iron cover, motor adapter and pump housing. No sheet metal parts to rust or corrode. All cast iron class 30, 30000# tensile strength.
• Stainless steel screws and handle.
• 20 ft. UL Listed 5-wire (1 PH) or 8-wire (3 PH) neoprene cord. Extra cords lengths available in 25′-35′-50′ length only. Sensor leads & power leads in one cord for easy installation.
• Threaded conduit connection for protecting cords in those extra heavy duty applications.
• Moisture sensors prewired in motor housing (requires indicator in panel).
• Zoeller custom designed panels with intrinsically safe re lays and moisture indicator are required.
• 3 phase models available.
• Motor - 60 Hz, 1750 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protected (3 phase requires circuit in control panel).
• Maximum temperature for sewage or dewatering 104°F (40°C).
• Shaft Seal - Stainless steel wetted parts, carbon & ceramic rotary face seal.
• Upper ball bearing and lower ball bearing running in bath of oil.
• Buna-n square ring seals.
• Both models pass 3” solids (sphere).
• Major width 16 1/8′′. Height 25 15/16′′.
• Available in nonautomatic units only.
• 4′′ horizontal flanged discharge - standard ANSI flanged.
• 100% computerized testing and 100% tested sub merged in water.
• Corrosion resistant powder coated epoxy finish.

For Additional Information including Performance Curve

• FM and cCSAus rated Class 1, Division 1, Group C & D.
• Non-Clogging semi-open ductile iron impeller.
• Class 30 cast iron construction.
• All units are double seal for extra motor protection.
• Corrosion resistant powder coated epoxy finish.
• Stainless steel screws, washers, tags and seal assembly
• 25 foot UL Listed power and sensor cord. Cord length also available in 50 foot.
• Single phase - 230V capacitor start, capacitor run.
• Three Phase - 200-230-460-575 Volt.
• Explosion proof motor - 60 Hz, 1750 RPM, oil-filled, hermetically sealed with heavy duty finned motor housing for added heat dissipation.
• Thermal sensor.
• Continuous duty operation in submerged conditions.
• Maximum temperature for sewage or dewatering 104°F (40°C) with 1.2 service factor (1.0 service factor on Model 661).
• 416 stainless steel motor shaft.
• Tandem shaft seals - stainless steel fitted, carbon/ceramic seal faces.
• Seal leak probes.
• Oversized upper & lower ball bearings running in an oil bath.
• Buna-N square rings and seals used throughout.
• All models pass 2 1/2′′ spherical solids
• Specify 3′′ NPT vertical, 3′′ horizontal flanged or 4′′ horizontal flanged discharge.
• 100% computerized tested.
• Major width 17 9/16′′. Height 33 1/4′′.
• Non-sparking rail systems available for all models.
• Intrinsically safe control panels available.
• All Single Phase Units Require External Starting Capacity And Relay Circuits.

  For Additional Information including Performance Curve

• Meet the specifications with assurance.
• Dewatering.
• A High Temperature submersible pump series with electrical components meeting the National Electrical Code requirements for 200° F service.
• Comprehensive line of models, styles and modes.
• Conduit length for nonautomatic is 6 feet.
• Cord length for automatic is 15 feet, conduit length from pump to switch is 3 feet.
• High Temperature liquid-tight conduit used with High Temperature cable.
• High Temperature motor windings.
• High Temperature Viton® gaskets.
• High Temperature thermal overload protected.
• All control components in contact with the water are High Temperature rated.
• All models have vortex impeller design.
• All models have stainless steel screws, guards, handles and control arm & seal assemblies
• Float operated mechanical switch box which is mounted on the discharge pipe above the operating level. (Switch box is not intended to come in continuous contact with 200° F water.)
• Nonautomatic models available.
• Mechanical seal has NI-Resist stationary face and Viton® elastomer.
• Corrosion resistant powder coated epoxy finish.

  For Additional Information including Performance Curve

For Additional Information including Performance Curve

• Non-clogging bronze vortex impeller design.
• Durable cast construction. Cast iron switch case, base, motor and pump housing.
• Castings - Cast iron class 25-30 (25,000# tensile strength). Impeller, bronze class 85-5-5-5.
• Corrosion resistant powder coated epoxy finish.
• 20 ft. UL Listed 3-wire neoprene cord and plug. Longer cords available in lengths of 25-35-50 feet.
• Motor - 60 Hz, 3450 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protection (1 Ph only).
• Upper sleeve bearing and lower ball bearing running in bath of oil.
• Carbon and ceramic shaft seal.
• Maximum temperature for effluent or dewatering, 130°F - 54°C (ED 140°F - 60°C).
• Major width 12 3/4”. Height 18 9/16”. (Single seal pumps)
• No screens to clog.
• Square Ring & Gasket - Neoprene.
• Stainless steel screws, bolts, float rod, handle guard, arm and seal assembly.
• Passes 3/4” spherical solids.
• 1 1/2” NPT discharge with 2” or 3” flange available.
• Automatic units available with float operated, submersible (NEMA 6) 2-pole mechanical switch. On point 14 3/4” - Off point 5”.
• Available in single or double seal designs.
• 100% of units are computerized tested.

  For Additional Information including Performance Curve

• Non-Clogging vortex impeller.
• Float operated, submersible (NEMA 6) 2-pole mechanical switch & variable level long cycle systems available.
• UL Listed 3-wire cord plug; 9 ft. standard for automatic, 15 ft. standard for nonautomatic.
• Corrosion resistant powder coated epoxy finish.
• No sheet metal parts to rust or corrode.
• Stainless steel screws, switch arm, guard and handle.
• No screens to clog.
• Watertight neoprene
• ring between motor and pump housing.
• Solid buoyant polypropylene float.
• Motor - 60 Hz, 1550 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protected.
• Upper and lower sleeve bearings running in bath of oil.
• Entire unit pressure tested after assembly.
• Carbon and ceramic shaft seal.
• Maximum temperature for effluent or dewatering - 130°F (54°C).
• Passes 1/2′′ inch spherical solids.
• 1 1/2′′ NPT Discharge.
• On point - 7 1/4′′;
• Off point - 3′′.
• Major width - 10 3/32′′.
• Height - 10 1/16′′.

Note: The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with nonautomatic pumps.

For Additional Information including Performance Curve

• Non-clogging vortex impeller design bronze class 88-8-0-4.
• Float operated, submersible (NEMA 6) 2-pole mechanical switch.
• Durable cast construction. Cast iron switch case, base, motor and pump housing. No sheet metal parts to rust or corrode.
• Stainless steel screws, bolts, float rod, handle, guard, arm and seal assembly.
• 20 ft. UL Listed 3-wire neoprene cord and plug. Extra cord lengths available in 25-35-50 foot length only.
• Motor - 60 Hz, 3450 RPM, oil-filled, hermetically sealed, automatic reset, thermal overload protected (1 Ph only).
• Maximum temperature for effluent or dewatering 130°F (54°C), WD189 120°F (49°C).
• Variable level control systems available.
• Square Ring & Gasket - Neoprene.
• Shaft Seal - Stainless steel carbon & ceramic rotary.
• Upper sleeve bearing and lower ball bearing running in bath of oil.
• All 180/4180 series pass 3/4-inch spherical solids.
• On point 14 3/4′′
• Off point 5′′ (automatic units).
• Major width 12 3/4′′
• Height 18 9/16′′. (Single seal pumps)
• 1 1/2′′ NPT discharge with 2" or 3′′ flange available.
• Corrosion resistant powder coated epoxy finish.

Warning : Model 185 should not be subjected to heads less than 30 feet TDH.

For Additional Information including Performance Curve

• Enclosed impeller design.
• Float operated, submersible (NEMA 6) 2-pole mechanical switch.
• Durable cast construction. Cast iron switch case, base, motor and pump housing. No sheet metal parts to rust or corrode.
• Stainless steel screws, bolts, float rod, handle, guard, arm and seal assembly.
• 20 ft. UL Listed 3-wire neoprene cord and plug. Extra cord lengths available in 25-35-50 foot length only.
• Motor - 60 Hz, 3450 RPM, oil-filled, hermetically sealed, automatic reset, thermal overload protected (1 Ph only).
• Maximum temperature for effluent or dewatering 130°F (54°C), WD189 120°F (49°C).
• Variable level control systems available.
• Square Ring & Gasket - Neoprene.
• Shaft Seal - Stainless steel carbon & ceramic rotary.
• Upper sleeve bearing and lower ball bearing running in bath of oil. Passes 5/8 - inch spherical solids.
• On point 14 3/4′′
• Major width 12 3/4′′
• Height 18 9/16′′. (Single seal pumps)
• 1 1/2′′ NPT discharge with 2′′ flange
• Corrosion resistant powder coated epoxy finish.

For Additional Information including Performance Curve

• Use fully or partially submerged.
• Durable polypropylene housing.
• 3-prong power cord, 9 ft. or 20 ft.
• 115 Volt/Single Phase/60 Hz.
• High quality sealed motor.
• Thermal-overload protected motor.
• Model 42 is adaptable for use with standard garden hose (fitting included), 1′′ NPT pipe, or 1¼′′ slip fit (use discharge hose kit P/N 1010-0117).
• Model 44 is adaptable for use with standard garden hose (fitting included), 1-1/4′′ Female NPT or 3/4′′ female NPT adapter.
• Model LM44 has automatic operation to be used in utility installations only. 
• Model 46 is 2′′ NPT discharge with 2′′ hose adapter.
• Screened bottom may be removed to allow easy cleaning.
• Use indoors or outdoors.
• Typical applications: dewatering and filling.
• Oil free (Models 42 and 44 only.)
• Models 42 and 44 remove water from any flat surface down to 1/8′′; model 46 will pump down to 1′′.
• Lightweight and Portable.
• Compact design: Models 42 and 44 will fit in a 7′′ opening; model 46 will fit in an 8′′ opening.
• One-year limited warranty.
• Temperature rating 120°F.
• Nonautomatic.

  For Additional Information including Performance Curve

• Non-clogging engineered plastic vortex impeller design.
• Corrosion resistant powder coated epoxy finish.
• Durable cast construction. Cast switch case, motor, pump housing and base. No sheet metal parts to rust or corrode.
• Castings - All cast iron class 25-30 25000# tensile strength.
• Stainless steel screws, guard, handle, arm and seal assembly.
• Float operated submersible (NEMA 6) 2-pole mechanical switch.
• Motor - Permanent split capacitor, 60 Hz, 1725 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protection.
• Bearings - Upper & lower oil fed cast iron.
• Carbon and ceramic shaft seal.
• Entire unit pressure tested after assembly.
• Watertight neoprene “” ring between motor and pump housing.
• Maximum temperature for effluent or dewatering 130°F - 54°C.
• Passes ½ inch spherical solids.
• No screens to clog.
• Standard cord length 15 ft. (UL Listed).
• 1½” NPT Discharge (1½” X 2” PVC Adapter included with BN & BE Models).
• On point - 9½”
• Off point - 3”
• Major width - 10 1/8”
• Height - 12”

  The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with nonautomatic pumps.

  For Additional Information

• Durable Cast Iron construction.
• Model 140 features a Non-Clogging engineered thermoplastic vortex impeller design, passes 1/2′′ spherical solids. 
• Model 145 features an engineered thermoplastic single vane impeller design, passes 3/4′′ spherical solids.
• Motor - 60 Hz, 3450 RPM, oil-filled, hermetically sealed, automatic reset, thermal overload protected.
• Available in both single or double shaft seal designs.
• Carbon/Ceramic seals.
• Assembled with Stainless Steel bolts.
• Upper sleeve and lower ball bearing running in bath of oil.
• 20 ft. UL Listed Neoprene cord with molded plug cap and ground wire.
• 1 1/2′′ NPT vertical discharge.
• Stainless steel lifting handle.
• BN and BE models include a variable level float switch and 1 1/2′′ X 2′′ PVC adapter fitting.
• Operates at temperatures to 130°F (54°C) in effluent or dewatering applications.
• Corrosion resistant powder coated epoxy finish.

  For Additional Information including Performance Curve

• 115V single phase/60 Hz, .3 HP, 3.1 Amps, 3400 RPM.
• Thermal overload protection.
• Non-corrosive engineered plastic motor housing, pump housing and base.
• No steel sheet metal parts to rust or corrode.
• All stainless steel screws, switch arm, and lower motor housing.
• Oil-free.
• 2-pole float operated mechanical switch.
• Solid buoyant polypropylene float.
• Engineered plastic impeller.
• UL Listed 9′ cord with 3-prong plug.
• Maximum temperature for dewatering - 110°F (43°C).
• Passes 3/8” inch spherical solids.
• 1 1/2” NPT discharge.
• Non-clogging vortex impeller.
• On point - 7 3/8′′
• Off point - 3 5/8′′.
• Major width - 9 1/16′′
• Height - 11 13/16′′.
• Variable level Float Switches available.
• Variable level long cycle systems available.
• Alarm systems available.
• Duplex systems available.

  For Additional Information including Performance Curve

• 115V single phase/60 Hz, 1/2 HP, 5.0 Amps, 3400 RPM.
• Thermal overload protection.
• Non-corrosive engineered plastic motor housing, pump housing and base.
• No steel sheet metal parts to rust or corrode.
• All stainless steel screws, switch arm, and lower motor housing.
• Oil-free.
• 2-pole float operated mechanical switch.
• Solid buoyant polypropylene float.
• Engineered plastic impeller.
• UL Listed 9′ cord with 3-prong plug.
• Maximum temperature for dewatering - 110°F. (43°C.)
• Passes 3/8” spherical solids.
• 1” NPT discharge.
• Non-clogging vortex impeller.
• On point - 8 1/2”
• Off point - 3 5/8”
• Major width - 9 1/16”
• Height - 12 5/8′′
• Variable level Float Switches available.
• Variable level long cycle systems available.
• Alarm systems available.
• Duplex systems available.

  For Additional Information including Performance Curve

Motor:
115 Volts, single phase, 60 Hz, 1/4 HP, 3.8 amps, 3450 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protected.
Motor Housing:
Rugged cast iron motor housing with corrosion resistant baked on enamel finish.
Efficient heat sink for heat dissipation.
Base/Pump Housing:
Glass-filled polypropylene with no screen.
Passes 3/8” spherical solids.
Impeller:
Non-Clog vortex impeller engineered glass-filled
Thermoplastic with metal insert.
Power Cord:
UL Listed 9 ft., 3-wire cord and plug.
Switch:
Reliable tethered float switch.
Seals:
Carbon & ceramic rotary seal.
Watertight neoprene seal between motor and cover.
Fasteners:
Stainless Steel Screws and hardware.
Temperature Rating:
104°F (40°C).
Cycle:
• On point - 11 1/4′′
• Off Point - 4 1/8′′.
Dimensions:
• Maximum width - 8 3/32 ′′
• Height - 10 1/2′′
• Weight - 11.0 lbs
• Fits 12′′ Diameter Pits

For Additional Information including Performance Curve