Pumps related categories
 | The Home Guard® MAX Pump
The Home Guard® MAX Pump
The HOME GUARD® MAX pump, installed as a standby to an electric sump pump, does not use any water, except during an emergency. In case of a power failure or other system malfunctions, the HOME GUARD® MAX takes over.
The water flow is equivalent to a normal faucet and required only when HOME GUARD® MAX is operating.
The HOME GUARD® MAX unit is not intended to serve as a primary water removal unit or to increase the capacity of an undersized primary unit. Its purpose is to be used as a back up to an electric sump pump due to power or pump failure. If the output of this unit is not sufficient to meet your specific demands, refer to our DC back up sump pump systems.
For Additional Information including Performance Curve |
 | The Aquanot Series Battery Backup Pedestal Sump Pump
Back up pump has heavy duty 12 volt motor and
positive contact float switch.
Stainless steel column and shaft.
Noncorrosive base assembly.
Discharges water as fast as many primary
pumps.
Aquanot I equipped with .5 amp battery monitor
designed to maintain a fully charged battery.
Aquanot II equipped with automatic electronic 25
amp charger to maintain and recharge battery.
Pump Alarm included with all Aquanot pumps.
*Warranty - 12 months from date of installation or 18 months from date of manufacture. However, the 12 month warranty is extended to 36 months with the purchase of an Aquanot battery by Zoeller.For Additional Information including Performance Curve |
 | X282-X284 Submersible Sewage or Dewatering Pump
- FM listed motor for Class 1, Division 1, Group C & D environments.
- Not for use in acidic, methanol, or ethyl acetate atmospheres.
- Non-clogging cast iron vortex impeller design.
- Stainless steel rotor shaft.
- Durable cast construction. Cast iron cover, motor adapter and pump housing. No sheet metal parts to rust or corrode. All cast iron class 30, 30000# tensile strength.
- Stainless steel screws and handle.
- 20 ft. UL listed 5-wire (1 PH) or 8-wire (3 PH) neoprene cord. Extra cords lengths available in 25′-35′- 50′ length only. Sensor leads & power leads in one cord for easy installation.
- 1 1/4′′ Threaded conduit connection for protecting cords in those extra heavy duty applications.
- Moisture sensors prewired in motor housing (requires indicator in panel).
- Zoeller custom designed mechanical switch or panel with intrinsically safe relays and moisture indicator is required.
- 3 phase models available.
- Motor - 60 Hz, 1750 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protected (3 Phase requires circuit in control panel).
- Maximum temperature for sewage or dewatering 104°F (40°C).
- Shaft Seal - Stainless steel wetted parts, carbon & ceramic rotary face seal.
- Upper ball bearing and lower ball bearing running in bath of oil.
- Buna-n square ring seals used throughout
- All models pass 2′′ spherical solids.
- Major width 13 9/16′′, Height 23 1/4′′.
- Available in nonautomatic units only.
- When ordering specify 2′′ or 3′′ NPT female flanged vertical discharge.
- 100% computerized testing and 100% tested sub merged in water.
- Corrosion resistant powder coated epoxy finish.
For Additional Information including Performance Curve |
 | X161-X163-X165 Submersible Effluent or Dewatering Pump
- FM listed motor for Class 1, Division 1, Group C & D environments.
- Warning : Not for use in acidic, methanol, or ethyl acetate atmospheres.
- Non-clogging vortex impeller design bronze class 88-8-0-4.
- Stainless steel rotor shaft.
- Durable cast construction. Cast iron cover, motor adapter and pump housing. All cast iron class 30, 30000# tensile strength.
- 20 ft. UL Listed 5-wire (1 PH) or 8-wire (3 PH) neoprene cord. Extra cords lengths available in 25′-35′-50′ length only. Sensor leads & power leads in one cord for easy installation.
- Threaded conduit connection for protecting cords in those extra heavy duty applications.
- Moisture sensors prewired in motor housing (requires indicator in panel).
- Zoeller custom designed mechanical switch or panel with intrinsically safe relays and moisture indicator is required.
- 3 phase models available.
- Motor- 60 Hz, 3450 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protected (3 phase requires circuit in control panel).
- Maximum temperature for effluent or dewatering 104° F (40°C).
- Shaft Seal - Stainless steel wetted parts, carbon & ceramic rotary face seal.
- Upper ball bearing and lower ball bearing running in bath of oil.
- Buna-n square ring seals.
- All models pass 3/4′′ spherical solids.
- Major width 13 5/16′′. Height 23′′.
- Available in nonautomatic units only.
- 1 1/2 NPT discharge standard, 2′′ & 3′′ NPT Flange available.
- 100% computerized testing and 100% tested submerged in water.
- Corrosion resistant powder coated epoxy finish, with stainless steel screws and handle.
For Additional Information including Performance Curve |
 | X404-X405 Submersible Sewage or Dewatering Pump
- FM listed motor for Class 1, Division 1, Group C & D environments.
- Not for use in acidic, methanol, or ethyl acetate atmospheres.
- Non-clogging vortex impeller design bronze class 88-8-0-4.
- Stainless steel rotor shaft.
- Durable cast construction. Cast iron cover, motor adapter and pump housing. No sheet metal parts to rust or corrode. All cast iron class 30, 30000# tensile strength.
- Stainless steel screws and handle.
- 20 ft. UL Listed 5-wire (1 PH) or 8-wire (3 PH) neoprene cord. Extra cords lengths available in 25′-35′-50′ length only. Sensor leads & power leads in one cord for easy installation.
- Threaded conduit connection for protecting cords in those extra heavy duty applications.
- Moisture sensors prewired in motor housing (requires indicator in panel).
- Zoeller custom designed panels with intrinsically safe re lays and moisture indicator are required.
- 3 phase models available.
- Motor - 60 Hz, 1750 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protected (3 phase requires circuit in control panel).
- Maximum temperature for sewage or dewatering 104°F (40°C).
- Shaft Seal - Stainless steel wetted parts, carbon & ceramic rotary face seal.
- Upper ball bearing and lower ball bearing running in bath of oil.
- Buna-n square ring seals.
- Both models pass 3” solids (sphere).
- Major width 16 1/8′′. Height 25 15/16′′.
- Available in nonautomatic units only.
- 4′′ horizontal flanged discharge - standard ANSI flanged.
- 100% computerized testing and 100% tested sub merged in water.
- Corrosion resistant powder coated epoxy finish.
For Additional Information including Performance Curve |
 | Model 913 Automatic Simplex Explosion Proof System
Applications- Ideal solution for quick change oil stations or other locations that require explosion proof equipment in the wash down area.
- Not for use in acidic, methanol or ethyl acetate atmospheres.
Any Public Facility:- Elevator pits
- Transportation and Utility Tunnels
- Hospitals & Schools
- Stadiums
- Stores & Restaurants
- Service Stations
- Hazardous Industrial areas
Features |
 | End Suction Centrifugal Pump
Zoeller Company is proud to announce the addition of the End Suction Centrifugal Pump to its product line. The pump housing is made of a durable cast iron construction allowing for a variety of applications, such as pressure boosting, circulation, irrigation, water transfer, and lawn sprinkling. Quality features include a heavy duty motor ranging from 1/3 HP to 2 HP, a four position discharge and mechanical seal and the flexibility to install in either the vertical or horizontal direction. Versatile and compact to fit in tight places, the End Suction Pump is available in 115 and 230 volt single phase. This pump comes preass-embled and ready for installation.For Additional Information including Performance Curve |
 | Lawn Sprinkler Pump
Zoeller Company is proud to announce the addition of the self-priming Lawn Sprinkler Pump to its product line.The unique design allows for proper lawn sprinkling saturation in areas where high water pressure is not available or inadequate. Quality features include a heavy duty motor ranging from 3/4 HP to 2 HP, a large volume pump housing that ensures quick and easy selfpriming operation, mechanical seal, and an air volume control connection. With a versatile and compact design to fit in tight places, these lawn sprinkler pumps can be field wired for 115V or 230V applications. This pump comes preassembled and ready for installation.For Additional Information including Performance Curve |
 | Qwik Jon® Sewage Removal Systems
Typical Installations
Versatile installation enables the pump compartment and piping to be concealed by the installation of a wall.
NOTE: Access must be maintained to the pump compartment.
NOTE: The Qwik Jon® is designed to fit flush with any elevated floor made of standard 2” x 6” material (actual dimensions 1 1/2” x 5 1/2”). And you can add a Lavatory - Bathtub - Shower with the installation of the 2” adapta-flex seal (provided). Tub or shower requires built in installation. Install a Qwik Jon® Just About anywhere
- Designed to accommodate a toilet, lavatory and a bathtub
- Use with a variety of toilet styles (1.6 Gallon residential flush)
- Perfect for basements, family rooms, warehouse, factories, room additions
- No need to destroy concrete floors
- Reduces construction cost
- Pumps any direction
- Fits just about anywhere
For Addiitonal Information |
 | Special Options Drain Pump
Applications include, laundry tray pump, wet bar sink, lavatory, air conditioning condensate or dehumidifier water removal. It can also be used in conjunction with dishwashers and garbage disposal applications. Drain Pump Series Includes: |
 | Drain Pump Series
Applications include, laundry tray pump, wet bar sink, lavatory, air conditioning condensate or dehumidifier water removal. It can also be used in conjunction with dishwashers and garbage disposal applications.Drain pump Series Includes |
 | Grinder Model 840
FEATURES- Durable Heavy Duty Finned Cast Iron Construction.
- 2 HP, 60 Hz, 3450 RPM.
- Oil-Filled - Hermetically Sealed Motor with Class F Insulation.
- Hardened Stainless Steel Cutter and Disc.
- Cutters Protected from Abrasive Solids.
- Cutters can automatically alternate direction to enhance blade life and free hang-ups. (automatic or manually)
- Stainless Steel Screws, Bolts, and Lifting Bail.
- Easily adapts to many existing competitors′ rail systems.
- Tandem seals with leak detection
- Automatic Thermal Overload Protection (Single Phase)
- Legs Provide for free standing installation.
- Preassembled Systems Available.
- Corrosion resistant powder coated epoxy finish.
For Additional Information |
 | Grinder Model 820
Grinder model 820 standard features:
1 1/4′′ NPT vertical dischargeCarbon/ceramic sealThermal overload protectionBalanced bronze impellerStainless steel cutter plate/cutterStainless steel shaftStainless steel hardware230V pumps are supplied with a 20 amp plug20′ Power cordWD & WH grinder pumps are completely automatic with starting controls in pump switch case. For Additional Information |
| The Shark 820 Field Mount System
Contact factory for control panel selection.
Access Doors Available on Field Mount Systems - Consult Factory
Special Basin Configurations - Consult Factory |
 | 810-815 Series Grinder Pump
Progressing Cavity Grinder Pump
1 and 2 HP Progressing Cavity
FEATURES:- Finned Class 30 Cast Iron Construction.
- Corrosion Resistant Powder Coated Epoxy Finish.
- Discharge Size - 1-1/4′′ NPT.
- 1 & 2 HP, 60 Hz, 1725 RPM.
- Model 810 - 1 HP, 230 Volts/1 Ph.
- Model 815 - 2 HP, 230 Volts/1 Ph.
- UL Listed 20 ft. 3-wire neoprene cord with 15 amp plug.
- Oil-Filled - Hermetically Sealed Motor with Class B Windings.
- Hardened Stainless Steel Cutter and Disc, Rockwell C55-60.
- Stainless Steel Hydraulic Pump Rotor.
Maximum operating temperature 130°F (54°C)For Additional Information
|
|
Tell your suppliers you found them on ThomasNet
