Hoists related categories
 | USA Hand Chain Hoists
Designed for long life with minimum maintenance, the BUDGIT USA family of hand chain hoists outstanding features include: lightweight, tight headroom, overload device standard, and
easy operation. The 1/4 thru 6-ton models are of the same basic construction and consist of a cast aluminum frame which houses an automatic load brake, spur gear reduction, and load sprocket with chain guide. Suspension hook is full swiveling.
Spark and Corrosion Resistant Models
Spark and corrosion resistant models, for both the USA Hand Chain and Aluminum Hand Chain Hoists, are designed for service in certain hazardous atmospheres and areas where resistance to friction sparks is vitally important. These models have: bronze alloy hooks, bronze block sleeves or aluminum lower blocks, special chrome nickel stainless steel alloy load chains; and aluminum or bronze hand chains.Notice: MILITARY SPECIFICATIONS — BUDGIT Aluminum Chain Blocks and Track
Clamps are on the Qualified Products List QPL-904 for military specifications. Contact
factory for prices and delivery. FURNISH COMPLETE ORDERING DATA
REQUIREMENTS.
Equipped with Hook Latches. Standard lift is 8 ft. Hand chain can drop approximately 1½
ft. above fully extended hook. |
 | HI-CAP2® Aluminum Army-Type Trolley Hoists
These integrally built trolley and hand chain hoist combinations produce a compactness with exceptional high hook lift and low headroom advantages. Hoist section contains all the fine design features of the BUDGIT Aluminum Hand Chain Hoists. The trolley section has side plates of extra heavy rolled steel and forged alloy steel wheels with sealed ball bearings. Hand geared type models are identical to the push type models except that wheel flanges on one side are geared and meshed with a pinion driven by a hand wheel and chain. |
| HI-CAP2® Low Headroom Trolley Hoists
These integrally built trolley and hand chain hoist combinations produce a compactness with exceptional high hook lift and low headroom advantages. Hoist section contains all the fine design features of the BUDGIT Aluminum Hand Chain Hoists. The trolley section has side plates of extra heavy rolled steel and forged alloy steel wheels with sealed ball bearings. Hand geared type models are identical to the push type models except that wheel flanges on one side are geared and meshed with a pinion driven by a hand wheel and chain. |
 | Steel Frame Hoists
BUDGIT Steel Frame Chain Hoists are designed, built, and tested to rigid specifications of quality and performance. They are thoroughly engineered from every standpoint; have been made light in weight, compact and sturdy enough to serve as a rigger’s hoist. Simplicity of design makes them easy to service and maintain, permits longer trouble-free periods of service. They are strong, durable and fully enclosed, and thus well suited for indoor or outdoor use under all hoisting applications.
Standard lift is 8′ - 0′′ with 6′ - 0′′ drop on hand chain hoist.
Maximum lift is 50 ft. |
 | Army Type Trolley Hoists
BUDGIT Army Trolley Hoists, in 1/4 to 2-ton capacities, are light weight and easily traverse minimum radius curves since the trolley units swivel. Construction is ingeniously simple. A standard BUDGIT super geared hoist is suspended on a special load bar carried at each end by a lifetime lubricated precision ball bearing equipped two wheel trolley. Trolley units are adjustable to beam size and are interchangeable. Plain trolley may be replaced with geared unit at any time, as required. Wheels have convex-machined treads that will maintain roundness through long use.
Note: All orders must specify exact beam size |
 | Steel Frame Low Headroom Trolley Hoists
BUDGIT Low Headroom Trolley Hoists are designed for applications where headroom is so limited that no other type hoist can be used. They offer an ideal solution in existing structures with low ceilings. This further suggests the possibility of interesting cost savings in new construction by allowing lower ceilings.
These hoist models are not adjustable to varying size beams. Each unit is custom built to fit the size beam specified in the order. However, the hoist can be built to operate on beams larger than standard. |
 | Steel Frame Swivel Truck Low Headroom Trolley Hoists
Low Headroom Trolley Hoist Incorporates two highly desirable features—compact low headroom design, and the ability to travel extremely short radius cruves without binding or scraping on the I-beam or monorail. Therefore, runways can be located closer to walls than would otherwise be possible with units of heavier and bulkier construction. And, like the standard low headroom type, this hoist also permits building to close headroom dimensions, with consequent savings in construction costs.
This trolley hoist is not adjustable to varying size beams. Each unit is custom-built to fit the size beam specified in the order. However, this hoist can be built to operate on beams larger than standard, and on either standard or wide flange beams. Be sure to specify height, type and flange width of I-beam. Curve radius must always be specified when ordering.
Note: Available with lifts longer than standard. |
 | Twin Hook & Extended Hand Wheel
Twin Hook Hoists
Two separate but connected spur gear hoists are driven simultaneously from a single hand chain. Long bulky loads can be easily and evenly lifted with the Twin Hook Hoist. Typical loads are: tubes, frames, lowers, drying and storage racks, auto and truck bodies, vats and tanks.
The suspension hooks can be hung from trolleys or from fixed positions.
Furnished with 3′ center distance between hooks are standard. Available with 4′ through 16′ center distances. Specify desired center distance. Center bearing required for distance 10′ or over. See price sheet. Only half of rated capacity of hoists is carried on each load hook. Exceeding one-half the rated capacity on each load hook when hooks are used together or individually can result in injury to persons and damage to property.
Extended Hand Wheel Hoists
This is a steel frame chain hoist with handwheel extended to allow the operator to stand at a distance from the load. Typical applications are:
handling hot materials from a distance, handling work whose surface must be protected from marring by the hand chain, or handling large, flat or bulky loads. The suspension may be from fixed supports or on trolleys. Inquire for
prices and information on unusually large capacities.
For Twin Hook Items, The List Price is with 3’ Center Distance Between Hooks |
 | Tugit 2 - Short Handle Model
Short Handle Model Features…
- 3/4 ton lever hoist has a 12′′ handle for close-quarter operation
- Handle is able to operate 360 degrees, making it convenient to operate
in any position
- Lightweight aluminum alloy construction for toughness and portability
- Double pawl allows for precise spotting of load
- Hardened alloy steel link type load chain for strength and durability
- Full swiveling forged steel upper and lower hooks with latches, standard on all models
- Positive acting Weston-type automatic load brake - weatherized for outdoor service
- Durable powder coat finish is standard
- Quick and easy one handled operation and control enables operator to rapidly change directions of chain travel
- Minimal effort required to pull on handle to lift full rated load
- Free wheel control permits free travel of chain so that it can be pulled thru hoist for fast attachment of load
- Metric rated
- Made in U.S.A.
|
 | Tugit 2 - Long Handle Models
Long Handle Lever Operated Hoist…
- Lightweight aluminum alloy construction for toughness and portability
- Hardened alloy steel link type load chain for strength and durability
- Full swiveling forged steel upper and lower hooks with with latches, standard on all models
- Positive acting Weston-type automatic load brake - weatherized for outdoor service
- Durable powder coat finish is standard
- Quick and easy one handed operation and control enables operator to rapidly change directions of chain travel
- Minimal effort required to pull on handle to lift full rated load
- Free wheel control permits free travel of chain so that it can be pulled thru hoist for fast attachment of load
- Metric rated
- Made in U.S.A.
|
 | USA Army Type Trolley Hoists
The BUDGIT USA Army Type Trolley Hoist is offered for those applications where
closer headroom is required. It consists of a lug suspension model BUDGIT USA
Hand Chain Hoist with a BUDGIT Rigid Mount Trolley. The lug hoist contains all
the fine features of the BUDGIT USA Chain Hoist with the exception of submitting
a lug suspension for the normal hook suspension. The rigid mount trolley is the
BUDGIT Rigid Mount Trolley outline on page 6, offering either a push type or hand
geared type traverse suspension. |
|
Tell your suppliers you found them on ThomasNet
