Pumps: Pressure related categories
 | The Home Guard® MAX Pump
The Home Guard® MAX Pump
The HOME GUARD® MAX pump, installed as a standby to an electric sump pump, does not use any water, except during an emergency. In case of a power failure or other system malfunctions, the HOME GUARD® MAX takes over.
The water flow is equivalent to a normal faucet and required only when HOME GUARD® MAX is operating.
The HOME GUARD® MAX unit is not intended to serve as a primary water removal unit or to increase the capacity of an undersized primary unit. Its purpose is to be used as a back up to an electric sump pump due to power or pump failure. If the output of this unit is not sufficient to meet your specific demands, refer to our DC back up sump pump systems.
For Additional Information including Performance Curve |
 | Multi-Stage Effluent Turbine Submersible Pumps
Effluent turbine pumps are used in on-site applications that demand more head than a traditional single stage centrifugal submersible pump. Zoeller Pump Company is able to meet this need by offering a complete line of submersible effluent turbine pumps. These pumps have been proven in field applications and have many years of development behind them. Typical applications include mound systems, drip systems, and recirculating media filters. All units include cool running submersible motors that do not require external water flow to prevent overheating. An outer pump sleeve is not required. Pumps can be installed directly in a dose tank as long as an effluent filter is used on the septic tank outlet. These pumps can also be used in conjunction with the Zoeller Effluent Turbine Filtered STEP system.For Additional Information including Performance Curve |
 | End Suction Centrifugal Pump
Zoeller Company is proud to announce the addition of the End Suction Centrifugal Pump to its product line. The pump housing is made of a durable cast iron construction allowing for a variety of applications, such as pressure boosting, circulation, irrigation, water transfer, and lawn sprinkling. Quality features include a heavy duty motor ranging from 1/3 HP to 2 HP, a four position discharge and mechanical seal and the flexibility to install in either the vertical or horizontal direction. Versatile and compact to fit in tight places, the End Suction Pump is available in 115 and 230 volt single phase. This pump comes preass-embled and ready for installation.For Additional Information including Performance Curve |
 | Lawn Sprinkler Pump
Zoeller Company is proud to announce the addition of the self-priming Lawn Sprinkler Pump to its product line.The unique design allows for proper lawn sprinkling saturation in areas where high water pressure is not available or inadequate. Quality features include a heavy duty motor ranging from 3/4 HP to 2 HP, a large volume pump housing that ensures quick and easy selfpriming operation, mechanical seal, and an air volume control connection. With a versatile and compact design to fit in tight places, these lawn sprinkler pumps can be field wired for 115V or 230V applications. This pump comes preassembled and ready for installation.For Additional Information including Performance Curve |
 | Model 50 Series Submersible Pumps
- Non-Clogging vortex impeller.
- Float operated, submersible (NEMA 6) 2-pole mechanical switch & variable level long cycle systems available.
- UL Listed 3-wire cord plug; 9 ft. standard for automatic, 15 ft. standard for nonautomatic.
- Corrosion resistant powder coated epoxy finish.
- No sheet metal parts to rust or corrode.
- Stainless steel screws, switch arm, guard and handle.
- No screens to clog.
- Watertight neoprene
- ring between motor and pump housing.
- Solid buoyant polypropylene float.
- Motor - 60 Hz, 1550 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protected.
- Upper and lower sleeve bearings running in bath of oil.
- Entire unit pressure tested after assembly.
- Carbon and ceramic shaft seal.
- Maximum temperature for effluent or dewatering - 130°F (54°C).
- Passes 1/2′′ inch spherical solids.
- 1 1/2′′ NPT Discharge.
- On point
- 7 1/4′′;
- Off point - 3′′.
- Major width - 10 3/32′′.
- Height - 10 1/16′′.
Note: The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with nonautomatic pumps. For Additional Information including Performance Curve |
 | Model 98 Cast Iron Series
- Non-clogging engineered plastic vortex impeller design.
- Corrosion resistant powder coated epoxy finish.
- Durable cast construction. Cast switch case, motor, pump housing and base. No sheet metal parts to rust or corrode.
- Castings - All cast iron class 25-30 25000# tensile strength.
- Stainless steel screws, guard, handle, arm and seal assembly.
- Float operated submersible (NEMA 6) 2-pole mechanical switch.
- Motor - Permanent split capacitor, 60 Hz, 1725 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protection.
- Bearings - Upper & lower oil fed cast iron.
- Carbon and ceramic shaft seal.
- Entire unit pressure tested after assembly.
- Watertight neoprene “” ring between motor and pump housing.
- Maximum temperature for effluent or dewatering 130°F - 54°C.
- Passes ½ inch spherical solids.
- No screens to clog.
- Standard cord length 15 ft. (UL Listed).
- 1½” NPT Discharge (1½” X 2” PVC Adapter included with BN & BE Models).
- On point - 9½”
- Off point - 3”
- Major width - 10 1/8”
- Height - 12”
The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with nonautomatic pumps. For Additional Information
|
|
Tell your suppliers you found them on ThomasNet
