Hinges: Cabinet related categories
 | Concession Hinges
Both leaves pierced with 0.203 inch diameter holes 2 inch centers, inline, 1/2 inch from edge.
|
| Pins for Continuous Hinges
Some Continuous Hinges are stocked with removable Pins. When necessary, these pins are available as separate item and can be purchased with different alloy pin to install in a particular hinge. |
 | Continuous Hinges with Countersunk Holes, Brass Plated
- Hole size: 0.040 inch material pierced and countersunk for #5 FH screw.
- Hole size: 0.060 inch material pierced and countersunk for #6 FH screw.
- Hole location: 2 inch center to center, in line
- Hinge pins are the same material as hinge.
|
| Continuous Hinges with Countersunk Holes, Nickel Plated
- Hole size: 0.040 inch material pierced and countersunk for #5 FH screw.
- Hole size: 0.060 inch material pierced and countersunk for #6 FH screw.
- Hole location: 2 inch center to center, in line
- Hinge pins are the same material as hinge.
|
| Continuous Hinges with Countersunk Holes, Aluminum
- Hole size: 0.040 inch material pierced and countersunk for #5 FH screw.
- Hole size: 0.060 inch material pierced and countersunk for #6 FH screw.
- Hole location: 2 inch center to center, in line
- Hinge pins are the same material as hinge.
|
 | Cabinet Pivot Hinges
- For 3/4′′ to 7/8′′ thick doors that completely overlap the frame
- Weight of door always carried on nylon washer - quiet operation
- Elongated screw holes on all leaves for vertical and horizontal adjustment
- Only the hinge pivot shows when door is closed
|
 | Furgocar Polished Stainless Steel Hinges
Ideal for : toolboxes, utility body compartments, industrial cabinets, machine shields, gates, storage boxes, shed doors, marine compartments and endless other applications. |
 | 550 Chest Hinges
Tight Pin. Countersunk Holes.
Designed for chests, cabinets, storage boxes, etc. Hinges and screws are semi-concealed when hinge is closed. |
 | Semi-Concealed Hinges
Designed as a semi-concealed, loose-pin hinge for 3/4′′ flush cabinet doors and shutters made of plywood. Used when end fastening would not be practical.
Removable pin allows hinge to be reversed for right- or left-hand applications.Both hinge leaves are concealed when the door is closed. |
 | Cabinet Hinges
- With removable pins
- The 1 1/2′′ (38.1 mm) size is three knuckle, the rest are five knuckle hinges
- For doors of cabinets, bookcases, china closets, etc.
- For full mortise type application
|
 | Cabinet Spring Hinge
- Steel, plated, highly rust resistant
- Use for flush surface application
- Spring action for self-closing doors
- For use on cabinet doors, utility closet doors, office gates.
|
 | Solid Brass Broad Hinge
- Finely finished solid brass fast spun pin hinge for use on small boxes, chests and cabinets
- Wide leaves for broad width applications
- Lacquered to resist tarnishing
|
 | Extra Heavy Full Surface Hinges
- For window grilles, steel shutters, iron gates or for general utility heavy duty requirements
- Made of extra heavy wrought steel, not swaged, for surface application, with fast spun pins
- Furnished on order, at additional cost, swaged for full mortise application, with screw holes
- Hinges as regularly furnished (not swaged) measure slightly less in width - approximately 1/8′′
- All sizes have five knuckles
|
 | Diecast Block Hinges
Block hinges are a neat, convenient method for hanging doors on metal cabinets, electrical enclosures, etc. Non-handed, the upper part simply lifts onto a fixed steel pin.
Four sizes are available, and they are supplied in chromium-plated, black, or raw metal finish (suitable for painting after assembly). |
 | Stainless Steel Block Hinges
These machined block hinges are available for high- quality cabinets, where stainless steel will completely overcome problems of corrosion, staining and binding- up, which can occur in damp or chemically-active environments.
Produced in three sizes, the hinges have a ground (satin) finish and are ready-lubricated with grease for smooth action. All edges are chamfered. |
|
Tell your suppliers you found them on ThomasNet
