Transducers related categories
 | LXT 930 - Reaction Torque Cell
The models LXT 930 Reaction Torque transducers are designed for installation between test pieces such as motors, switches, axles or shafts and their mounting plate. These models operate in both directions. Utilizing bonded strain gages and no moving parts, these models are maintenance free. |
 | LXT 932 - Flange Torque Cell
The models LXT 932 Reaction Torque transducers are designed for installation between test pieces such as motors, switches, axles or shafts and their mounting plate. These models operate in both directions. Utilizing bonded strain gages and no moving parts, these models are maintenance free. |
 | LXT 950 - Rotating Torque Cell
The LXT 950 is a slip ring rotating transducer which provides accurate measurements of bolt or nut wrenching torques. This transducer is tightening and break-away torques can be measured. Calibration of mechanical torque wrenches may be performed with this transducer. |
 | LXT 963 - Rotating Torque Load Cell
The LXT963 is designed to measure rotating drive torque using a conventional shaft-to-shaft configuration. This design incorporates a slip ring assembly which transmits excitation voltage to, and output signals from, the rotating sensor. If purchased with the DPI 2000, a personality module may be purchased for quick interfacing to that meter. Available as optional features are speed, angle encoder, and foot mount. |
 | LXT 970 Series Rotating Torque Load Cell- Square Drives- Male/Female
The LXT 970 torque transducer operates on the principle of magnetoelasticity. The sensors output signal is caused by a change in the magnetic field created by an applied torque on the sensor′s shaft. Non-contact detectors, in close proximity to the shaft, detect changes in the magnetic field and provide an electrical signal proportional to the torque. The electronics in the sensor provide signal conditioning suitable for use in industrial and process applications. The zero output is 2.5v. The output span can range from lOmv/v to 2.5v in either direction. |
 | LZBS 1020 - Fastener Force Transducer
The LZBS 1020 is a miniature load cell developed to measure fastener clamping forces. This design provides high stiffness in a small envelope, making the LZBS 1020 ideal for static and dynamic measurements on fasteners, tie rods or similar structural test applications where space limitations exists. Washers are not supplied with higher capacity units. The washers are to be mounted on either side of the transducer to minimize transmitted rotation effect and spot loading. The top washer should be mounted with the chamfered side toward the bolt head, to provide clearance for any fillet at head and shaft interface. The applied force must be uniformly distributed across the loading surfaces of the transducer. |
 | PLC 105 - Low Cost Pressure Transducer
The Model PLC 105 and PBW 2200 are low cost alternative pressure transducers offering good performance in high volume applications. Stainless steel construction provides durability to survive rugged environments. The PBW 2200 offers a 0-5 vdc or 4-20 ma amplified output while the PLC 105 has a nominal 2 mv/v output. These transducers are able to handle both liquid and gas pressure with safe overloads to 50% of capacity. |
 | PSG 110 - Miniature Pressure Transducer
This subminiature pressure transducer is designed to accurately measure pressure ranges from 15 psi to 20,000 psi. Manufactured with a stainless steel diaphragm, the one piece design allows for a thin diaphragm but heavy sidewalls. This enables the transducer to be used in rugged environments while still being able to measure in low ranges. These transducers have a small electrical zero balance circuit board which is in the lead wire (approx. 1′′ x .087′′ thick). |
 | PSG 120 - Subminiature Transducer
The Models PSG 120 and PSG 122 are subminiature pressure transducers manufactured with a unitized stainless steel diaphragm allowing for a thin diaphragm and heavy side walls from one piece of stainless steel. This design produces a very sensitive but rugged transducer able to cover the entire pressure range from 15 psi to 15,000 psi. The PSG 120 and PSG 122 transducers are ideal in corrosive fluid environments and are recommended for applications involving rough handling or where a completely hermetically sealed transducer is required. |
 | PTG 135 - Precision Pressure Transducer
The model PTG 135 (gage pressure) is designed for rugged industrial applications requiring high accuracy pressure measurements. These transducers are designed with 4 arm 350 ohm strain gage bridge and have welded stainless steel construction. Using a ′′True Gage′′ design, the PTG 135 utilizes a second welded diaphragm that hermetically seals the strain gage circuitry which allows the transducer to reference atmospheric pressure. The PTA 145 absolute pressure units utilize an internally sealed 0 psia reference. All transducers have excellent long term stability. |
 | PTA 145 - Absolute Pressure Transducer
The model PTA 145 (absolute pressure) is designed for rugged industrial applications requiring high accuracy pressure measurements. These transducers are designed with 4 arm 350 ohm strain gage bridge and have welded stainless steel construction. Using a ′′True Gage′′ design, the PTG 135 utilizes a second welded diaphragm that hermetically seals the strain gage circuitry which allows the transducer to reference atmospheric pressure. The PTA 145 absolute pressure units utilize an internally sealed 0 psia reference. All transducers have excellent long term stability. |
 | PTG 230 - General Purpose Pressure Transducer
The PTG 230 is designed as a general purpose industrial pressure transducer. Pressure ranges span from 0.5 to 60,000 PSIG. These transducers have stainless steel construction and utilize a complete four arm 350 ohm strain gage bridge. The PTG 230 uses standard gage design. The PTA 232 has an internally sealed 0 psia reference. |
 | PTA 232 - Absolute Pressure Transducer
The PTA 232 is designed as a general purpose industrial pressure transducer. Pressure ranges span from 0.5 to 60,000 PSIG. These transducers have stainless steel construction and utilize a complete four arm 350 ohm strain gage bridge. The PTG 230 uses standard gage design. The PTA 232 has an internally sealed 0 psia reference. |
 | PTG 400 - General Purpose Pressure Transducer
The PTG 400 is a competitively priced, high quality all stainless steel, pressure sensor intended for use in the measurement of gases and liquids. This series is suitable for automotive diagnostics tools, refrigeration, hydraulics, pneumatics and data loggers. The PTG 400 pressure sensors are designed specifically for applications with demanding price and performance requirements. These sensors offer both millivolt and high level outputs. The high strength sensing element is machined from a solid piece of stainless steel, resulting in construction that contains no silicone oil, welds or internal O-rings. Measurements are available in gauge pressure covering ranges up to 10,000 PSI. |
 | PWD 305 - Low Range Differential Pressure Transducer
The PWD Wet/Wet Differential pressure transducers utilize a bidirectional design which accepts fluid in both ports to measure full scale differential pressures from 0.5 to 150 psid. Overload stops and stainless steel construction are standard features, providing added durability, impressive accuracies of 0.25% to 0.5% full scale are achieved over a wide variety of line pressures. Typical applications include flow measurement, depth sensing, pressure equalization, and liquid level. |
 | PST 175 - Submersible Pressure Transducer
The PST 175 is a high accuracy, high quality all stainless steel media isolated pressure transducer intended for use in the measurement of liquids compatible with stainless steel, Polyurethane and Polyolefin. This series is suitable for industrial and water management applications. The PST 175 has been designed specifically for applications with demanding price and performance requirements. The double jacketed cable ensures protection against rough handling and extreme protection against cable collapse. PST 175 submersible sensors offer a choice of high level outputs. The high
strength stainless steel construction contains no silicone oil, no welds and no internal O-rings. Measurements are available in gauge pressure covering ranges up to 100 PSI. The PST 175 is ideal for applications needing high accuracy, excellent long-term stability, trouble free
operation, long life and high performance in harsh environments.
|
 | LXT 971 Series Rotating Torque Load Cell- Shaft to Shaft
The LXT 971 torque transducer operates on the principle of magnetoelasticity. The sensors output signal is caused by a change in the magnetic field created by an applied torque on the sensor′s shaft. Non-contact detectors, in close proximity to the shaft, detect changes in the magnetic field and provide an electrical signal proportional to the torque. The electronics in the sensor provide signal conditioning suitable for use in industrial and process applications. The zero output is 2.5v. The output span can range from lOmv/v to 2.5v in either direction. |
 | PWD 360 Wet/Wet Differential Pressure Transducer
The PWD 360 offers wet/wet differential pressure measurements for media compatible with stainless steel. The compact size contains no internal O-rings or fluid filled cavities, making it ideal for applications including water management, gas pipeline instrumentation, filtration, and natural gas compressors. These are
among a few of the many applications the PWD 360 can handle. In the event that either pressure port is at full line pressure and the other at zero, no damage will be done to the transducer/transmitter. On board digital
compensation with analog through path ensures low thermal errors with fast response times. Both voltage and current outputs are available over a wide operating temperature range. Measurements are available in
differential pressures covering line pressures up to 1,000 PSI.
|
|
Tell your suppliers you found them on ThomasNet
